APPLICABLE MATERIAL:
- Steel
- Copper
- Aluminium
- Galvanized steel
- PVC
- CPVC
- Stainless steel
- Polyethylene
- Polypropylene
- Cast-iron
- Concrete
- FRP/GRE
CHEMICAL RESISTANCE:
- Oil
- Water (drinking water, wastewater, steam)
- Solvents (acetone, toluene, MEK, ethyl alcohol)
- Mild acids (hydrochloric acid, sulfuric acid) and alkalis
- Chemical (ethylene glycol, xylenes, ammonia)
- Hydrocarbons
- Bases
- Slurries
- Fuels (petroleum, diesels, gasoline)
- Gases (LNG, LPG)
- Organic salts
WORKING TIME (FIBERGLASS TAPE):
1 minute at 30 °C (86 °F)CURING TIME:
- 30 minutes at 30 °C (86 °F)
- Heat may be applied to decrease curing time
- Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.
APPLICATION:
- Pipe repairs
- offline repairs
- sealing joints
- hazardous material spill control
- reinforce thinning walls
- Abrasion protection
- Structural reinforcement
- Repairs in hard to reach areas
- Underwater repairs
OPERATING TEMPERATURE:
- Continuous – From -29 °C (-20 °F) up to 200 °C (392 °F)
- Intermittent – From 200 °C (392 °F) up to 320 °C (570 °F)
OPERATING PRESSURE:
- Recommended for pressure up to 400 psi (28 kg/cm2)
- (Results vary depending on pipe size, type of pipe, hole size, pipe content, and method of application)
APPLICABLE INDUSTRIES:
Building & Facilities
Electronics 
Irrigation
Industrial Processing
Oil & Gas 
Chemical 
Marine
Manufacturing Plants 
Military
Offshore
Food Processing 
Petrochemical
Pharmaceutical 
Wastewater 
Power Generation 
Pulp & Paper
Water Distribution
WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:
1
Stop the pipe flow
Stop the pipe flow
2
Roughen the area to be repaired
Roughen the area to be repaired
3
Knead the Seal Stic
Knead the Seal Stic
4
Apply the Seal Stic to fill holes or cracks in the damaged or leaked area.
Apply the Seal Stic to fill holes or cracks in the damaged or leaked area.
5
Immerse the Wrap Seal Fiberglass Tape into water
Immerse the Wrap Seal Fiberglass Tape into water
6
Wrap the Wrap Seal Fiberglass Tape around the repair area as tightly and evenly as possible, using the entire roll
Wrap the Wrap Seal Fiberglass Tape around the repair area as tightly and evenly as possible, using the entire roll
7
Discard the plastic tube at the end of the roll
Discard the plastic tube at the end of the roll
8
Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap
Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap
9
Continue to polish the wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance
Continue to polish the wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance
PACKAGE:
- 1 roll of Wrap Seal Fiberglass Tape
- 2″ x 5′ (50 mm x 1.2 m)
- 2″ x 6′ (50 mm x 1.8 m)
- 2″ x 12′ (50 mm x 3.6 m)
- 3″ x 9′ (75 mm x 2.7 m)
- 4″ x 12′ (100 mm x 3.6 m)
- 1 unit of Seal Stic Quick Cure Epoxy
- 1 pair of latex gloves
- Operating instruction